发表了科研论文 200 余篇，其中被 SCI 和 EI 收录 100 余篇，CSCD 收录近 100 篇。典型论文：

1. Zhang xuefeng, A Plantar Pressure Sensing System with Balancing Sensitivity Based on Tailored MWCNTs/PDMS Composites, Micromachines, 2018.09, SCI000448399300048

2. Wang juan, Effect of Ni doping on electrochemical performance of Li3V2(PO4)3/C cathode material prepared by polyol process,Ceramics International,2014.08, SCI000337015300136

3. Xie miaoxia, Microstructure and mechanical properties of CP-Ti_X65 bimetallic sheets fabricated by explosive welding and hot rolling,Material and Design, 2015.08, SCI000363816000022

4. Zhao nannan,Loss Calculation and Thermal Analysis of Surface-Mounted PM Motor and Interior PM Motor,IEEE Transactions on Magnetics, 2015.11, SCI000364770500482

5. Li pengju, Experimental Investigation on the Film Pressure Measurement in Microgap Water-Lubricated Hybrid Journal Bearing, Tribology transactions, 2017.10, SCI000417649800007

6. Ye xiangdong, A facile method to fabricate surfaces showing superhydrophilicity in air and superhydrophobicity in oil, Science China-technological sciences, 2017.8, SCI000415011900012

7. Yang naixing, Effects of Temperature Differences Among Cells on the Discharging Characteristics of Lithium-Ion Battery Packs with Series/Parallel Configurations during Constant Power Discharge, Energy technology, 2018.06, SCI000435271700009

8. Gu lichen, A new evaluation method on hydraulic system using the instantaneous speed fluctuation of hydraulic motor, Proceedings of the institution of mechanical engineers part c-journal of mechanical engineering science, 2018.08, SCI000441286200010

9. Wu xiaojun, Study of trajectory and experiment on steel polishing with elastic polishing wheel device, International Journal of Advanced Manufacturing Technology, 2018.07, SCI000435594100016

10. 苏晓峰，基于PLC的工业自动化立体仓库控制系统设计[J].自动化与仪器仪表，2016（3）：119-121

11. 王苗，基于粒子群算法的惯性水平振动给料机的优化[J].山东煤炭科技，2016（12）：179-181

12. 杨蕾，电火花线切割加工参数对加工速度和表面粗糙度影响的研究[J].机床与液压，2011（15）：45-47

13. 杨蕾，基于Labview的电火花线切割放电加工状态的研究[J].仪器仪表与传感器2012（3）:41-43

14. 杨蕾，基于虚拟仪器的电火花线切割放电状态检测系统[J]. 机械工程师2011(9):56-58

15. 刘金颂，基于Zernike矩和PSO算法的摄像机神经网络标定[J].光电子•激光,2010,21(9):1311-1314（EI：20104113293263）

16. Jin-Song Liu, Stereo matching using SIFT and rotation invariant uniform LTP[C]. Proceedings of the International Conference on Advanced Technology of Design and Manufacture, Beijing, 2010:209-213 (EI:20120514722418)

17. 刘金颂， 基于PSO和LSSVM回归的摄像机标定[J].光电工程, 2010, 37(5):47-51（CSCD核心）

18. 刘金颂，Zernike矩和曲率的圆形中心亚像素定位[J].计算机工程与应用, 2010, 46(29):153-155（CSCD核心）

19. 刘金颂，双目立体视觉中的摄像机标定技术研究[J].计算机工程与应用, 2008,44(6)237-239（CSCD核心）